Built for working events
- Tool-Free InstallationNo tools, no hardware kits — the frame walks open by hand.
- Portable & ConvenientFolds into a wheeled roller bag one person can move.
- Quick SetupTwo people go from bag to branded booth in about 60 seconds.
- FrigostableFabric and hardware stay flexible down to -25°C.
- Heavy Duty HardwareReinforced truss and 58 lb-rated joints for daily event use.
- Reliable & DurableCommercial-grade build backed by our satisfaction guarantee.
Frame & hardware details
Click any image to zoom in on the Full Wall Booth Package — Trade Show frame, bag and included hardware.
10x10 Custom Canopy Tent — Trade Shows
SKU: PCT-P5-1010-TS
Starting At $1,349.00
- • Printed backwall, two half walls and table cover
- • Complete 10x10 booth in one wheeled bag
- • 100 sq ft enclosed-on-three-sides booth
- • Lifetime hardware warranty
Product specs
- Material
- 600D Weatherproof Polyester (CPAI-84 Fire Rated)
- Print Method
- Full Color Dye-Sublimation (Edge-to-Edge)
- Dimensions
- 10ft x 10ft (100 Sq. Ft. Coverage)
- Hardware
- 40mm Aluminum Hex Frame
- Setup Time
- Approximately 5 Minutes (2 People)
- Warranty
- Lifetime Hardware Warranty · 2-Year Canopy Material
- Production
- 3–4 business days after artwork approval
Customize This Package
Product Details
This is a complete 10x10 trade show booth, not just a tent. A printed backwall anchors the space, two half walls close the sides to counter height so passers-by can still see in, and a matching stretch table cover fronts the booth. It replaces a pipe-and-drape rental at roughly the cost of two show rentals, and it goes up in ten minutes without a labor call.
Key Features
- Three-Wall Booth System: Full backwall plus two counter-height half walls define the space while keeping the aisle open.
- Matching Table Cover: Printed 6 ft stretch cover cut from the same artwork as the walls.
- No Labor Call Required: Two people, ten minutes, no tools — skip drayage and installation fees.
- Fire-Retardant Certification: CPAI-84 paperwork included for convention-center fire marshals.
- Reprint-Ready Frame: Refresh graphics season to season without replacing the aluminum frame.
What is the best 10x10 trade show display setup?
A printed canopy frame with a full backwall, two half walls and a matching table cover gives you the most branded surface per dollar in a 10x10 inline booth. It ships in one wheeled case, sets up in ten minutes without labor, and reads as a finished environment rather than a folding table under fluorescent light.
Compare that to renting pipe and drape plus a banner stand: after two or three shows you have spent more than the package costs and own nothing. The other advantage is consistency — the same kit works at an indoor convention hall and an outdoor expo, so field teams learn one setup. Reserve the backwall for a single message and a logo; crowded backwalls read as noise from the aisle.
This package is built specifically for trade show operators running a 10x10 footprint. The full kit configuration covers the branded surface most trade show teams actually use week to week, and it upgrades cleanly — walls, table covers, flags and weight bags all attach to the same frame later without a reprint of the top.
How much does a custom trade show canopy cost?
Custom 10x10 canopy booths run roughly $650 for a printed top and frame to about $1,350 for a complete kit with backwall, half walls and a table cover. Price scales with printed surface area, not frame quality — every package here uses the same commercial aluminum frame.
There are no per-color, setup or artwork fees on any package. Costs that do vary: rush production, additional sizes, and replacement tops when campaigns change. Because the hardware carries a lifetime warranty, most buyers plan on one frame purchase and periodic graphic refreshes at roughly half the package price.
Setup and care
Two people set this canopy up in about a minute: walk the frame open from opposite corners, clip the printed top over the truss, then extend the legs one notch at a time so the fabric tensions evenly. Ballast every leg before you load the booth. Clean the top with mild soap and warm water, never a pressure washer, and always pack the fabric dry. Store the frame and top in the included roller bag out of direct sunlight between events.
Related Packages
Frequently Asked Questions
+Can a pop up canopy be used as a trade show booth?
Yes. A 10x10 canopy with a printed backwall and half walls covers the same footprint as a standard inline booth and delivers far more branded surface area than pipe and drape, at a one-time cost instead of a per-show rental.
+Will convention centers allow this tent indoors?
Most will, with CPAI-84 fire-retardant documentation and weight plates instead of stakes. Confirm the show's maximum booth height, which is often 8 feet for inline spaces.
+How long does the booth take to set up?
About ten minutes with two people: frame, top, backwall, half walls, then the table cover.
Customers Also Bought
Complete the setup
This printed canopy tent works hardest when it is not alone: custom table covers dress the counter, feather flags mark the approach, and canopy side walls close the booth off when wind or rain arrives.
Teams working trade shows, festivals and sports events also keep spare tent accessories on hand — sandbags, a wheeled carry bag and replacement parts that fit the same 40mm frame.
Prefer a single line item? Our complete event tent kits bundle the same components by industry, or browse the full product catalog to build it piece by piece.
Prop 65 Warning: This product can expose you to chemicals including DINP, known to the State of California to cause cancer. For more information go to www.P65Warnings.ca.gov.